Petrophysics · Reservoir economics

Is Low Resistivity Pay a Good Pay?

Pay is a rock verdict. Good pay is an economic verdict.

Is Low Resistivity Pay a Good Pay? Gate 1, Storage: is the hydrocarbon really there? Gate 2, Flow: will it flow at a rate worth having? Gate 3, Value: what does it cost to find out and to produce?
Three gates every low-resistivity interval has to pass: storage, flow and value.

An interval can pass every pay cutoff on the books, get carried into the reserves report — and still barely flow.

I have seen that interval more than once. On paper it is pay. In the well, it is a disappointment that someone paid good completion money to discover.

So let me ask the question I think our discipline asks too rarely. Not “is it pay?” — but “is it good pay?”

Those are different questions, and confusing them is expensive.

Three questions hiding inside one

When we call something low-resistivity pay, we usually mean one thing: the resistivity log says water, but the rock actually holds movable hydrocarbon.

Fair enough. Decades of work have taught us why resistivity can lie — laminated sand–shale sequences, dispersed clay adding its own conduction, conductive minerals like pyrite, microporosity full of bound water, fresh formation water that kills the contrast. Diagnose the mechanism, correct the saturation, and an interval that looked wet can turn out to be genuinely hydrocarbon-bearing.

That work matters. I have spent a good part of my career on it.

But notice what it actually answers.

  1. Gate 1Storage

    It answers the storage question: is there hydrocarbon in the pore space?

  2. Gate 2Flow

    It does not answer the flow question: will that hydrocarbon come out at a rate worth having?

  3. Gate 3Value

    And it certainly does not answer the value question: what will it cost us to find out, and to produce it?

Most of the low-resistivity pay literature stops at question one. Most of the disappointments live in questions two and three.

Pay cutoffs are volumetric. Production is not.

Here is the uncomfortable arithmetic. Our pay cutoffs — porosity above a line, water saturation below a line, shale volume below a line — are statements about volume. They tell us how much hydrocarbon sits in the rock.

A well does not produce volume. It produces rate.

Rate depends on permeability, on relative permeability at the actual saturation, on how far the interval sits above the free-water level, on the pore-throat system that decides which fluids move and which stay put. None of that is in a cutoff. An interval can clear every volumetric hurdle with room to spare and still fail every flow test that matters.

And here is where the mechanism — the thing we worked so hard to diagnose — comes back, because each mechanism fails, or succeeds, in its own way.

Laminated pay Often flows

Laminated pay often flows better than people fear. The shale laminae suppress the resistivity reading, but the sand laminae themselves can have perfectly respectable permeability. Perforate across them properly and the interval can perform like the conventional pay it secretly is.

Microporosity pay Storage without rate

Microporosity pay is the opposite trap. The bound water in the micropores does not flow — that part is reassuring. But rock dominated by micropores tends to have low permeability overall, so the oil rate is limited from day one. You book real reserves. You get a thin stream. Storage without rate.

Dispersed clay pay High water cut

Dispersed clay pay carries a different risk: high irreducible water saturation and unfavourable relative permeability mean the interval may come in with a high water cut and stay there. It produces, certainly. It just produces a lot of water alongside the oil, and water has to be lifted, handled, and disposed of — at a cost, every day, for the life of the well.

Conductive-mineral pay Pleasant surprise

Conductive-mineral pay — pyrite and its cousins — can be the pleasant surprise. The low resistivity is essentially an electrical artefact; the host rock's flow properties may be entirely normal. Diagnose it correctly and you may be looking at genuinely good pay that a resistivity-based workflow nearly threw away.

Same log response. Four completely different production behaviours. That is why “low-resistivity pay” is a diagnosis, not a verdict.

There is a quieter consequence, too. Reserves are meant to represent quantities that can actually be produced economically under current conditions. Volumes booked on pore space alone, in rock that will never flow at a commercial rate, have a way of coming back — as revisions, as write-downs, as awkward questions in an audit. Correcting a saturation is good science. Booking the result without asking the flow question is where good science turns into bad accounting.

The same interval, two different answers

Now the third question — value — because this is where I see the most money quietly lost.

Imagine an LRP interval that will add, say, a modest volume of reserves and a modest initial rate, declining from there. As a standalone project — its own completion programme, its own perforating run, dedicated testing, facilities sized for it — the returns can be genuinely poor. The capital is real and immediate; the production is small and spread thin over years.

Now put the same interval inside a well that is already being drilled or worked over for a primary target. Adding it costs a few extra perforations and a bit of evaluation. Suddenly the incremental barrel is cheap, and the same rock that failed the standalone test passes the incremental one comfortably.

Nothing about the geology changed. The economics inverted.

This is also why I resist the opposite error — writing LRP off entirely. An unperforated interval behind pipe in an existing well is an option. It costs almost nothing to hold. Prices change. Technology changes. A zone that does not pay today, at today's costs, may pay perfectly well in five years. Booking it carefully, understanding its mechanism, and keeping it in the inventory is not optimism. It is portfolio management.

What I do object to is spending completion money to test a hope. If the interval matters, verify cheaply first: revisit the old logs with the mechanism in mind, add one targeted measurement rather than a full suite, sample or test small before committing to a full completion. Spend the small money to earn the right to decide about the big money.

So — is it good pay?

My honest answer, after years of looking at these intervals: sometimes, and the resistivity curve cannot tell you when.

Before completing an LRP interval, I want three sets of answers:

  • Geology: What is the mechanism? What do the pore throats and the height above the free-water level imply for what will actually move?
  • Engineering: Is there an existing wellbore? Can the interval be commingled or added incrementally, and can we handle the water if the cut is high?
  • Economics: What is the incremental cost per incremental barrel — as a standalone project, and as a by-rider in a well we are drilling anyway?

If those answers are good, low-resistivity pay can be some of the most satisfying barrels in a field — reserves other people walked past. If they are bad, the most professional thing we can do is book it honestly, hold the option, and spend the capital somewhere it earns more.

Neither over-optimism nor throwing value away. Just the discipline of asking all three questions before the perforating guns go in the hole.

#Petrophysics#ReservoirEngineering#OilAndGas#LowResistivityPay